Radial X-Amp

The Radial X-Amp™ is an active Reamper™ that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to new possibilities and enhances the creative process so that your recording stands out.

• Active Reamp® with two outputs

• 100% discrete class-A signal path

• Transformer isolated to eliminate noise

• LED peak indicator and level control

Reamp for professionals
Following the critically acclaimed Radial JD7™ Injector, the X-Amp employs a unique class-A circuit design that has been optimized for use with guitars. Features include balanced line level input with LED peak indicator and level control, class-A circuit topology for optimal reach and frequency response, a transformer isolated output to eliminate hum and buzz caused by ground loops, a 180° polarity reverse switch to bring both amps into phase, and a dual ground lift switch for noise-free operation.

FEATURES

XLR In
Balanced +4dB line level input is used to receive the audio signal from the recorder. Follows AES standard with pin-1 ground, pin-2 hot (+), pin-3 cold (-). 

Ground
Lifts pin-1 ground on the XLR input, diverting the ground connection to the ¼” OUT-1. 

Power
15VDC 400mA power supply connection for the supplied external supply.

No Slip Pad
Neoprene isolation pad provides electrical isolation from the chassis and mechanical insulation from rough handling.

Power LED
Automatically illuminates when the power supply is connected. Lets you know the X-Amp is on and ready to use.

Level
Lets you adjust the X-Amp output level going to the amplifiers.

Clip LED
Provides visual cue of input signal. When this light goes on, turn down the source! You are overloading the X-Amp input circuit.

Out-1
Direct buffered output is used to feed your first amp. This should be a properly grounded amp that has passed local safety approvals.

180º Polarity
Reverses the absolute phase on output 2 so that both amplifiers play in phase. It can also be used to create different effects. 

Out-2
Transformer isolated output is used to feed your second amp while eliminating ground loops. 

Connector
Nylon XLR connector with extra large nickel-silver pin contacts. Tougher than steel.

100% Discrete
Full sized parts are hand inserted to deliver the very best audio quality.  Class-A circuit design for pure tone.

Transformer
Provides 100% isolation to eliminate hum and noise caused by ground loops.

Ground Lift
Applies to guitar amp output 2 - provides alternate ground path if needed or can help eliminate ground loops.

Circuit Board
Double-sided military spec for greater durability and full ground plane to reduce radio frequency interference. 

14-Gauge Steel
I-Beam construction prevents circuit  board from torque which could  lead to part failure.

SPECIFICATIONS

Audio circuit type: 100% discrete class-A
Frequency response: 20Hz ~ 15kHz (± 1.0dB)
Dynamic range: 119dB
Total harmonic distortion: 0.02% @ -15dBu
Intermodulation Distortion: 0.02% @ -20dBu
Input Impedance: 600Ω
Noise Floor: OUT-1 -110dB; OUT-2 -108dBu
Maximum Input: +22dBu
Features: 180° polarity reverse, Ground lift, Level Control
Input Connectors: XLR
Output Connectors: 1/4" Isolated and Direct
Construction: 14 gauge steel chassis & outer shell
Size (L x W x D): 3.3" x 5.0" x 2" (84 x 127 x 48mm)
Weight: 1.55lb (720g)
Shipping size (L x W x D): 5" x 2.75" x 10.75" (127 x 70 x 273mm)
Shipping weight: 2.6lb (1.18kg)
Power: +15VDC/400mA adapter included
Conditions: For use in dry locations only between 5°C and 40°C
Warranty: Radial 3-year, transferable

For more information, click here to visit the manufacturers website.